Product Code | NCSOLOC6 |
---|---|
Brand | Solo |
Capacity |
Approx. 4 litres |
Dimensions (HxDia) |
150x65mm |
Suitability |
Domestic life safety CO detectors |
Weight | 0.01kg |
Product Datasheets | Solo C3 and C6 MSDS |
Solo C6 – Hand-held Carbon Monoxide Detector Tester
Designed for use with domestic carbon monoxide (CO) detectors, the Solo C6 is a hand-held tester spray that does not require specialist equipment, such as dispensers. It is supplied with an applicator straw, which introduces CO to the detector sensor in a controlled manner.
For testing domestic carbon monoxide detectors
Hand-held – no need for specialist dispensing equipment
Supplied complete with applicator straw
Introduces CO to the detector sensor in a controlled manner
Contents: approx. 4 litres
Non-flammable, compressed gas
Due to the nature of the contents, the aerosol feels very lightweight
Please note: For testing FireAngel CO-9B and CO-9X carbon monoxide detectors, please use the FireAngel Easy Gas tester spray.
Description
Related products
Solo 365 Field Service Pack
Unlike other electronic detector testing systems, the Solo 365 does not require manufacturer refurbishment or servicing when any single component breaks, as the high-use parts are available for replacement by the user. The field service pack contains all user-replaceable components for the Solo 365 smoke detector test head, allowing engineers to carry spares everywhere they go to almost completely eliminate downtime due to damaged or worn-out equipment. Containing a cup and membrane, smoke generator module, and a battery, this kit includes almost everything needed to keep a Solo 365 in working order.
Designed for use only with Solo 365 equipment
Easy to install, field-replaceable design – no service requirement
Test more detectors in less time by carrying spares instead of going back to the van
The field service pack contains:
1x Cup & Membrane
1x Smoke Generator
1x Lithium Ion Battery Pack
Small, lightweight component designs make carrying spares far easier
Reduced downtime due to damaged equipment
Please note: ES3 smoke cartridges and the universal charging kit are not included in this pack.
Solo C3 – Carbon Monoxide Detector Tester
The Solo C3 carbon monoxide (CO) detector tester spray is designed for use in conjunction with the Solo 330 dispenser. Used in this controlled manner, the canister safely tests a CO detector by introducing a measured amount of CO gas to the sensor, whilst maintaining concentration levels below the toxic threshold. The Solo C3 tester is non-flammable and is supplied in a non-hazardous pressurised canister.
Introduces CO gas to the detector sensor
Non-flammable
To be used in conjunction with the Solo 330 dispenser
A measured amount of CO gas is delivered in a controlled manner
Concentration levels below the user danger level
Supplied in a non-hazardous pressurised 250ml canister
Please note: Some carbon monoxide detectors require a low level of CO present over a long period of time. It is unlikely that the Solo C3 will be suitable for testing these types of detectors.
Testifire 9202 9m Smoke/Heat/CO Detector Testing Kit
The Testifire 9202 Smoke/Heat/CO detector tester system offers the longest reach of any remote testing apparatus. By boasting the ability to combine a 4.5 metre telescopic access pole with up to three standard extension poles, this kit allows users to highly customise the reach of the system. This massively improves its potential range compared to the standard version. As stated the kit is modular, meaning it can be used to access devices at standard heights as well as enabling climb-free access to detectors on even the highest ceilings. Removing the need for extensive scaffolding creates immense time saving benefits for those conducting commercial detector testing. With automated test initiation, bespoke programmable test cycles and the longest reach available, the Testifire 9202 kit offers a versatile and complete system. Purchasing this kit is guaranteed to lead to long term time and cost saving benefits compared to the alternatives. This ultimate kit is completed with a universal detector removal tool and free protective storage/carry bag.
Kit includes:
Testifire 2000 Smoke/Heat/CO detector tester
TS3 smoke capsule
TC3 carbon monoxide capsule
Two solo battery batons
Solo 727 fast charger
Solo 100-001 fibreglass 4.5m telescopic access pole
Solo 101-001 fibreglass 1.13m extension pole
Solo universal detector removal tool
Solo protective carrying/storage bag
Automated infra-red test initiation
User friendly programmable interface
Multiple test modes and test cycles
Highly customisable test sequences including simultaneous testing
Colour coded LED user feedback
Automatic power-off feature after 5 minutes of inactivity to extend battery life
No pressurised containers needed - stimuli created on demand for smoke and CO sensors
Testifire 2001-001 Smoke/Heat/CO Detector Testing Kit
This product has been designed to revolutionise commercial fire alarm testing. The Testifire 2002 kit allows trained personnel to carry out "functional" testing on remote smoke, heat and carbon monoxide (CO) sensors without the need for scaffolding, harnesses or ladders. This presents the obvious safety benefits, but also allows users to save an estimated 45 minutes per day by removing the need to set up platforms etc. The device creates the necessary stimuli as needed, meaning there is zero waste, and also offers a clearing function meaning you can move on from having tested a device confident in the knowledge it is clear and ready to go.
Kit includes:
Testifire 2000 Smoke/Heat/CO detector tester
TS3 smoke capsule
TC3 carbon monoxide capsule
Two solo battery batons
Solo 727 fast charger
User friendly programmable interface
Automated infra-red test initiation
Multiple test modes and test cycles
Highly customisable test sequences including simultaneous testing
Automatic power-off feature after 5 minutes of inactivity to extend battery life
No pressurised containers needed- both smoke and CO created on demand
Solo 101 – Extension Access Pole
The Solo 101 extension access pole, designed for use on its own or in conjunction with a Solo telescopic pole, allows for detector testing equipment to be used at normal ceiling height or up to a maximum working height of 9 metres. The extension access pole negates the need for ladders or expensive scaffolding and therefore ensures that alarm technicians fully comply with the Safe Working at Height Directive.
Pole length: 1.13m
Can be used:
On its own to reach normal ceiling height
In conjunction with a Solo telescopic access pole for additional height
With Testifire and Solo testing devices
Ideal for use with Solo detector equipment including:
Solo 330 Smoke Dispenser
Solo 461 Cordless Heat Detector Test Kit
Solo 423 & 424 Mains Powered Heat Detector Testers
Solo 200 Universal Detector Removal Tool
Ensures compliance with the Safe Working at Height Directive
Allows for "functional" testing to be carried out
Testing equipment can be used at heights up to 9 meters using three extension poles and the Solo 100 or 108 access poles
Non-conductive glass fibre construction protects engineer from inadvertent shorts
Solo 365 Universal Charging Kit
The Solo 365 Universal Charging Kit allows engineers to charge their Solo 365 batteries from almost any power source. Containing the correct type of USB cable for the battery and CE Marked transformer, the selection of changeable international plug faces enable even the most far-reaching companies to benefit from the new Solo 365 detector testing equipment. As it uses a standard USB connection this kit even works with most portable power banks and laptops, allowing the Solo 365 to be recharged almost anywhere.
Designed for use with the Solo 365 Battery Pack
Works with most USB power sources and a wide range of international power supplies
Supplied with transformer block to provide optimum voltage and current
Simple click-on plug face design
No large "power brick" required, reducing bulk and weight for transportation
Please note: The Solo 365 Head & Core Components Kit includes a Universal Charger Kit as standard.
Solo 460 – Cordless Heat Detector Tester – Head Unit Only
The head unit only of the Solo 461 cordless heat detector tester is ideal for instances where you may have more than one technician working on site, or simply to replace a tester that has come to the end of its life. Using Cross Air Technology where heated air is blown across the cup, the Solo 460 cordless heat detector tester head unit provides rapid detector activation without the need for wiring. Replacement head unit only for the Solo 461 Cordless Heat Detector Tester Kit No wiring required - powered by battery batons (not included) Designed for use on fixed temperature, rate-of-rise and combination detectors to up 90 °C/194 °F (not Sabre) Lightweight and easy to use Test cup design allows clear view of the detector LED Uses Cross Air Technology: air is heated, blown across the cup and directed at the detector sensor Suitable for use at height, low levels and angles Suitable for use in conjunction with Solo telescopic access poles Provides rapid detector activation Please note: this listing is for the tester head unit ONLY. For the full kit including battery batons and charger, please see Solo 461 Cordless Heat Detector Tester Kit.
Solo 200 – Universal Detector Removal Tool
With the ability to create various size combinations, the Solo 200 universal detector removal tool is designed to suit the majority of smoke, CO and heat detectors for removal, inspection and replacement. The Solo tool has colour coded grips that simply twist in to place and the universal joint allows the tool to remain parallel with the ceiling. This makes it ideal for the removal of detectors installed in sloping ceilings. The Solo detector removal tool is to be used in conjunction with a Solo telescopic access pole and can also be used as part of a Testifire system. Universal design suits a wide range of detectors Various size combinations created with the colour coded twist grips Ideal for detector removal, inspection and replacement Quick and easy to use Suitable for the removal of detectors installed on sloping ceilings Designed for use in conjunction with a Solo telescopic access pole