Showing 1–12 of 26 results

Uniphos Gas Detector Tube

More than 200 different UNIPHOS Gas Detection Tubes are available-accurately make spot measurements for over 500 gases and vapours. The short-term UNIPHOS Gas Detection Tubes are used with the ASP-40 Air Sampling Pump. Gas detector tubes provide a simple measurement technique-detect toxic gas concentration in air samples. The tubes are pre-calibrated and take only a few minutes-complete sampling. The concentration is read directly from the length of color stain. Features
  •  Highly specific-target gas
  •  Simple device
  •  No requirement of complicated accessories
  •  No requirement of specialist-operate
  •  It is pre-calibrated and reads directly the target gas concentration
  •  Available for most of the industrial toxic gases and chemical vapours
Application Areas

It is useful for the air monitoring at work place & confined space in Industries like:

  •  Petrochemical & Refineries
  •  Pharmaceutical
  •  Chemical & Fertilizer
  •  Fumigation
  •  Food Industry
  •  Pulp & Paper Mills Industries
  •  Power & Steel Plants
  •  Municipal Corporations
  •  Environmental monitoring agencies and many more

KwikSense Smart Digital Gas Transmitter

KwikSense series digital gas transmitter is a field mountable device suitable for the detection and continuous monitoring of hazardous gases at industrial locations. It provides an RS-485 MODBUS-RTU digital output signal that can be connected to any suitable control system viz. Uniphos controller, DCS, PLC, etc. It also provides an industry standard 4-20 mA analog output. The KwikSense is available for a large number of toxic and flammable gases viz. CO, H2S, SO2, Cl2, NH3, HCN, HCl, NO2, CH4 (%LEL), etc. Features
  •  Plug & Play Smart Sensor Technology
  •  8x2 backlit alphanumeric LCD display
  •  Non-intrusive calibration using magnetic wand
  •  Tricolor LED for alarm indications
  •  Fully configurable on-board potential free relay contact
  •  Industry standard 4-20mA analog signal output (soft tunable)
  •  3x inbuilt 3 potential free relay contacts (optional)
  •  Input (24V) voltage monitoring and its status prompting on display
  •  Cable fault detection and 4-20mA output signal disable
  •  Inbuilt ambient temperature sensor
  •  User settable alarm set-points
  •  Provision to mute relay output
  •  Self testing of alarm LEDs and relays
  •  Indication for no sensor, over-range, baseline drift
  •  Digital communication by RS 485
  •  CIMFR/ PESO/ ATEX certified to Exd IIC T6, IP66
Application Areas

It is useful for the air monitoring at work place & confined space in Industries like:

  •  Refineries
  •  Cylinder storage yards
  •  Oil and gas industries
  •  Steel industries
  •  Chemical and fertilizer plants
  •  Pharmaceutical plants
  •  Power Industrie
 

KwikDraw Tubes

The combination of KWIK-DRAW™ detector tubes and pumps offers a quick yet precise measuring system to detect hazardous gases and vapours. The filling material in detector tubes is calibrated and adjusted to the required test gas and will change colour if this gas is present. The length of this discoloration indicates the concentration of the hazardous gas or vapour and can be measured by a printed scale on most of the tubes.

10015366-Sampling Hose for Kwik-Draw Deluxe detector tube pump -15 mtr

10015366-Sampling Hose for Kwik-Draw Deluxe detector tube pump -15 mtr

4523500-Dräger X-act® 5000, shoulderstrap without power supply

4523500-Dräger X-act® 5000, shoulderstrap without power supply

4523525-X-ACT 5000 Alkaline Battery Pack, T4 w/o Batteries (6 batteries required)

4523525-X-ACT 5000 Alkaline Battery Pack, T4 w/o Batteries (6 batteries required)

4523545-X-ACT 5000 Wall-Wart Charger 100 – 240 VAC (worldwide)

4523545-X-ACT 5000 Wall-Wart Charger 100 – 240 VAC (worldwide)