SMS with double outer chemical barrier 82 g/m².
Agriculture / Green Areas
Enhanced protection against chemicals
No risk of lint
Supports head movement for increased comfort
Closure with double flap
Double thumb loops
Good hold of the glove on the hand
REGULATION (EU) 2016/425
EN ISO 13688:2013 General requirements for protective clothing.
This standard specifies general performance requirements for ergonomics, innocuousness, size designation, durability, ageing, compatibility and marking of protective clothing and the information to be supplied by the manufacturer with the protective clothing.
EN14605:2005+A1:2009 Performance requirements for clothing with liquid-tight (Type 3) or spray-tight (Type 4) connections.
|TYPE||3B||Protection against liquid chemicals + biological protection – Type 3B (jets)|
|TYPE||4B||Protection against liquid chemicals (mists) – Type 4B|
This standard sets out the minimum requirements for the following types of limited use and re-useable chemical protective clothing:
– Clothing protecting the full body with liquid-tight connections between the various clothing parts (Type 3: liquid-tight clothing) ;
– Clothing protecting the full body with spray-tight connections between the various clothing parts (Type 4: spray-tight clothing) ;
Note: These standards were formerly entitled EN1512 (Type 4) and EN1511 (Type 3).
EN ISO 13982-1:2004+A1:2010 Protective clothing for use against solid particulates – Type 5 clothing
|TYPE||5B||Protection against dust (asbestos) + biological protection Type 5B|
This standard sets out the minimum requirements for chemical protection clothing resisting penetration of solid particulates suspended in air (type 5).
This clothing offers full body protection, including the torso, arms and legs, such as one or two-piece coveralls, with or without hood or face-shield, with or without foot protection.
EN13034:2005+A1:2009 Performance requirements for chemical protective clothing offering limited protective performance against liquid chemicals (Type 6 equipment)
|TYPE||6B||Limited protection against liquid chemicals + biological protection Type6B|
This standard sets out the minimum requirements for limited use and reusable, limited performance, chemical protective clothing. Limited use chemical protective clothing is intended for use in cases of a potential exposure to light sprays, liquid aerosols or low-pressure, low-volume splashes, against which a complete liquid permeation barrier (at the molecular level) is not required.
EN14126:2003+AC:2004 Protective clothing – Performance requirements and tests methods for protective clothing against infective agents
Associated with standards for protective clothing against chemical products, the letter B is added after the garment type. Examples: TYPE 6-B / TYPE 5-B / TYPE 4-B / TYPE 3-B
EN1073-2:2002 Protective clothing against radioactive contamination. Requirements and test methods for non-ventilated protective clothing against particulate radioactive contamination.
|CLASS||1||Radioactivité – Facteur de protection 5 – Classe 1|
The garments are classified according to their nominal protection factor (ratio between the concentration of test particles in the ambient atmosphere and the concentration of test particles inside the garment), determined in relation to the total inward leakage (ratio between the concentrations of test particles insider the garment and inside the test chamber).
The classes are as follows:
EN1149-5:2018 Electrostatic properties – Part 5: Material performance and design requirements
WARNING: These requirements may be insufficient in oxygen enriched flammable environments. This standard is not applicable for protection against mains voltages. The control of undesirable static electricity on the person is often necessary.
The electrostatic potential may, indeed, have serious consequences on the charged individual, because it can be high enough to cause dangerous sparks.
After a risk assessment, the wearing of protective electrical dissipation clothing may be necessary. The use of clothing certified according to EN1149-5 is then adapted.
The ATEX Directive 1999/92/EC, in its Annex II-A-2.
3, requests that workers be equipped with work clothes made of materials that do not produce electrostatic discharges that can ignite explosive environments.
The electrostatic potential can also affect equipment sensitive to electric discharge. And antistatic clothing are often used on electronic manufacturing sites, assembling semiconductors for example. Finally, they are used on sites with controlled atmospheres such as automotive paint workshops, to avoid the emission of particles that may be deposited on the body paint.
The antistatic charge dissipation can be provided by a process limiting the build up of charge, or by adding carbon or metal wires. People wearing protective electrostatic charge dissipation clothing must always be grounded with a resistance of less than 10⁸Ω, for example, by wearing appropriate footwear such as the safety shoes stated in EN ISO 20345, or by other suitable means.